Lucifer black LED mirrors with Oi flash controller for sportsbike

by KiWAV Magazi
0 Rating
You save:
In Stock
SKU: 100182719000003
EAN: 0680577050426
Fitment Color Sold in Units

Oi flash controller changes the original lighting into a lively art performance by combining fade-in / fade-out type and flashing type light with different tempo combinations.
It's completes your custom motorcycle project to a full A+ grade. Package includes two Oi flash controllers and a pair of Lucifer black neat stem LED mirrors for most Harley Davidson bikes.

8 combinations of running and indicator lights set up - magazi Lucifer LED mirrors with KiWAV Oi flash controller
Oi 16 flash modes demo video

Sealed LED module with IP67 dust & waterproof compliant.

→ What does IP67 waterproof rating mean?

IP67: Ingress protection, Solid particle protection, Liquid ingress protection

IP6x is the highest dust resistance rating, so this product is fully protected against dust.
IPx7, the second-highest water resistance rating, means this product can withstand immersion in water up to one meter (3.3 feet) for 30 minutes, tested in laboratory conditions.

Code Effective against Description
6 Dust tight No ingress of dust; complete protection against contact (dust tight). A vacuum must be applied. Test duration of up to 8 hours based on air flow.

Code Protection against Test duration Description
7 Immersion, up to 1 m depth 30 mins Protected from immersion in water with a depth of up to 1 meter (or 3.3 feet) for up to 30 mins
Lucifer LED Motorcycle mirror turn signal, driving light, in the daylight, at night, in total darkness
  • Feature
    1. Oi flash controller with Lucifer LED mirrors completes your custom motorcycle project to a full A+ grade..
    2. Two-tone color LED lights, various combinations of driving and indicator lights set up.
    3. Waterproof and dustproof LED modules.
    4. Stylish designs for your custom applications.
    5. Wider vision with convex lens and E-mark approved.
    6. *Sealed LED module with IP67 dust & waterproof Compliant.
  • Oi Flash Controller SPEC
    ♦ 16 different modes that can be applied to your stop light, turn signal light, hazard light, and decoration light.
    ♦ Operate in the voltage range from 6.5V to 16V. (Suitable for 12V vehicle power system)
    ♦ Ambient temperature must not below -20° (-4°F) and not exceed +85° (185°F).
    ♦ Works both for​ halogen ​& LED bulbs.
    ♦ Super-duper easy set up for LED lights. NO LOAD RESISTOR IS NEEDED.
    ♦ Maximum current rating up to 8A. (Suitable for up to 4 light bulbs with 21W)
  • Material
    Mirror Housing: ABS plastic
    Mirror Stem: Aluminum
  • Shape
    Diamond / Other
  • Glass
    Chrome Convex Lens
  • Mirror Wire Length
    620mm / 24inch
  • Color
    Mirror plate: matt black LED: White: 2 PCS (12V / 0.9W), Amber: 7 PCS (12V / 0.9W)
  • Adjustment
    High adjustable (three adjusting joints)
  • Weight
    n.w.: 820 g./ 1.8 lbs. (pair),
    g.w.: 1220 g/ 2.68 lbs. (total package, packing inclusive)
  • Package
    a pair ( Left hand / Right hand ),
    Oi flash controller x 2 pcs,
    adapter with toothed adjustment joint x 2 PCS,
    rubber mounting gasket x 2 PCS,
    M6 bolt 25 mm long x 4 PCS,
    M6 bolt 40 mm long x 4 PCS,
    M6 nut x 4 PCS,
    big washer x 4 PCS, small washer x 4 PCS
  • Fitment
    Suitable for hole spacings C2C on the fairing from 26 mm to 55 mm.
    See the Fitment List

    ATTENTION!Oi Flash Controller is designed to replace a 3-pin flasher relay ONLY (not for a 4 or 5 pin relay, it will destroy the device).

  • Installation

    1. Please refer to your service manual to remove the original mirror.
    2. Temporarily fix the mirror to the bolt fixing position of the vehicle, using the base rubber, bolts (those with matching length or genuine one), washers and nuts. (See the figure below)
    3. Once temporarily fixed to the left and right, please adjust the whole position using hexagon wrench at the two bolts at the bottom of the mirror.
    4. Tightening each part after the position is finally fixed.

    Installation Guide of KiWAV Lucifer LED mirrors for sportsbike
  • Connect to the Turn Signal

    ♦ There is no need to replace the relay when using this product with exisiting blinkers.
    ♦ Relay is needed when using this product as the only turn signal.
    ♦ Minor modification might be required depending on motorcycles.

    Check the wiring of the vehicle on the manufacturer service manual, refer to the wiring table below, and connect the turn signal wiring with the attached electro tap.
    Also, please wire the position line (white) of this product to the accessory power supply of each vehicle.

    A table of this product and main manufacturer blinker wiring colors:
    Running Light (-) Right Turn Signal (+) Left Turn Signal (+)
    Lucifer black yellow yellow
    Honda green light blue orange
    Yamaha black deep green brown
    Suzuki black / white light green black
    Kawasaki black / yellow grey green

    Each manufacturer wiring color in the table is for reference only, it depends on the vehicle year and specifications, please be sure to confirm with the service manual issued by the manufacturer and connect it.

    In order to use this product safely please understand and work on the followings:
  1. These are not plug & play parts, motorcycle electrical knowledge is required.
  2. For removal / installation of genuine parts and tightening of bolts / nuts, please be sure to perform based on the manufacturer's issued service manual.
  3. We are making every effort to manufacture and making sure its quality, but please do not install if there is any incompleteness in the item if any.
  4. Please stop using it immediately if any faults happen.
  5. Although this device has been designed to significantly increase your lighting visibility, flash/strobe patterns may not be street legal in your area.
  6. *Protected from dust / Protected against the effects of immersion in water to depth between 15cm and 1 meter.
  7. Minor modification might be required.
  8. Warranty is voided if any of the above are not followed.
  9. Newer Harley-Davidsons run the "indicator flash rate" through the OEM TSM/TSSM modules. You can not use Oi flash controller if the OEM TSM/TSSM modules include the circuit of your motorcycle.

*Please allow measuring deviation due to manual measurement.

Measurement of Lucifer with new generation light Oi flash controller

How to install mirrors for sport bike on your motorcycle

Check the video below to follow the step by step of the installation:

How To Install Mirrors For Sportbike On Your Motorcycle

Check the video below to follow the step by step of the installation:

There are yet no reviews for this product.

Please log in to write a review. Log in