LED mirrors Lucifer with sequential effect carbon for Sportsbikeby Magazi
Sealed LED module with IP67 dust & waterproof compliant.→ What does IP67 waterproof rating mean?
IP6x is the highest dust resistance rating, so this product is fully protected against dust.
IPx7, the second-highest water resistance rating, means this product can withstand immersion in water up to one meter (3.3 feet) for 30 minutes, tested in laboratory conditions.
|6||Dust tight||No ingress of dust; complete protection against contact (dust tight). A vacuum must be applied. Test duration of up to 8 hours based on air flow.|
|Code||Protection against||Test duration||Description|
|7||Immersion, up to 1 m depth||30 mins||Protected from immersion in water with a depth of up to 1 meter (or 3.3 feet) for up to 30 mins|
- Two-tone color LED lights. White light as the running light, yellow light as the turn signal.
- Turn signal light up in sequence, from the inside outwards.
- Sealed LED module with IP67 dust & waterproof compliant.
- Stylish designs for your custom applications.
- Wider vision with convex lens and E-mark approved.
- Easy installation.
Mirror Housing: ABS plastic
Mirror Stem: Aluminum
Diamond / Other
Chrome Convex Lens
n.w.: 700 g./ 1.54 lbs. (pair),
g.w.: 1100 g/ 2.42 lbs. (total package, packing inclusive)
Mirror plate: carbon fiber pattern
LED: White: 2 PCS (12V / 0.9W), Amber: 7 PCS (12V / 0.9W)
High adjustable (three adjusting joints)
620mm / 24inch
a pair ( Left hand / Right hand ),
adapter with toothed adjustment joint x 2 PCS,
rubber mounting gasket x 2 PCS,
M6 bolt 25 mm long x 4 PCS,
M6 bolt 40 mm long x 4 PCS,
M6 nut x 4 PCS,
big washer x 4 PCS, small washer x 4 PCS
Suitable for hole spacings C2C on the fairing from 26 mm to 55 mm.
See the Fitment List
1. Please refer to your service manual to remove the original mirror.
2. Temporarily fix the mirror to the bolt fixing position of the vehicle, using the base rubber, bolts (those with matching length or genuine one), washers and nuts. (See the figure below)
3. Once temporarily fixed to the left and right, please adjust the whole position using hexagon wrench at the two bolts at the bottom of the mirror.
4. Tightening each part after the position is finaly fixed.
Connect to the Turn Signal
♦ There is no need to replace the relay when using this product with exisiting blinkers.
♦ Relay is needed when using this product as the only turn signal.
♦ Minor modification might be required depending on motorcycles.
Check the wiring of the vehicle on the manufacturer service manual, refer to the wiring table below, and connect the turn signal wiring with the attached electro tap.
Also, please wire the position line (white) of this product to the accessory power supply of each vehicle.
A table of this product and main manufacturer blinker wiring colors:
Running Light (-) Right Turn Signal (+) Left Turn Signal (+) Lucifer black yellow yellow Honda green light blue orange Yamaha black deep green brown Suzuki black / white light green black Kawasaki black / yellow grey green
Each manufacturer wiring color in the table is for reference only, it depends on the vehicle year and specifications, please be sure to confirm with the service manual issued by the manufacturer and connect it.
- In order to use this product safely please understand and work on the followings:
- 1. This is only suitable for skilled users, others please find the nearest dealers.
- 2. For removal / installation of genuine parts and tightening of bolts / nuts, please be sure to perform based on the manufacturer's issued service manual.
- 3. Please stop using it immediately if any faults happen.
- 4. We are making every effort to manufacture and making sure its quality, but please do not install if there is any incompleteness in the item if any.
- 5. Warranty is voided if any of the above are not followed.
*Please allow measuring deviation due to manual measurement.
There are yet no reviews for this product.
Please log in to write a review. Log in